• 100% solids. Does not contain solvents. No strange smells. Free of emissions into the atmosphere.
• Good adhesion to concrete with high mechanical resistance, resistance to abrasion and chemical agents.
• Suitable for indoor applications.
• Excellent resistance to extreme temperatures (-40 ºC and +90 ºC). Breaking temperature 200 ºC.
• Provides completely waterproof floors, resisting permanent contact with water, hydrolysis and attack by microorganisms.
• Once the pavement is cured it is not toxic.

Before applying the product, check that the support is clean and free of traces of oil, grease, silicone, contaminating waxes or soil materials. If repair is needed, apply appropriate repair mortars.
Apply at room temperature between +8 ºC and 30 ºC. The temperature of the support must be between +10 ºC and 35 ºC. The support must be dry and with relative humidity < 85% (Maximum residual humidity of the support < 4%).

It is important to control the dew point to prevent condensation from occurring and avoid whitish areas on the coating.
It is necessary to start from a porous concrete support, without grout and free of curing liquids. Minimum compressive strength of concrete: 15 N/mm2. Minimum tensile strength of concrete: 1 N/mm2.
If in doubt, carry out a test before application.
Primer: Prime the support with FUTURPRIMER UNIVERSAL.
Finishing: Apply 2 coats of FUTURFLOOR PU2K SELF-LEVELING.
Mix the two components in the recommended proportion of 4 parts by weight of component A for every 77 parts. Component B: 23 parts wt.
Beat component A well in its container, then add component B and beat with an electric stirrer (300-400 rpm) for a minimum of 2 minutes until obtaining a homogeneous product. If overmixed, occluded air bubbles may appear. Once the two components are mixed, it is ready for use. The open application time (Pot Life) is 20-30 minutes at 25 ºC and < 85% RH.

Apply with a notched trowel and spiked roller. Apply the product by pouring. Pour continuously to avoid the formation of air pockets until the desired thickness is achieved.
Application rate: 1.5 Kg/m2 in 1 mm thick layers. The final consumption will depend on the porosity and roughness of the support.
Repainting will be done once the previous layers have dried, approximately 8-24 hours. Do not repaint after 48 hours.

Touch dry 2-3 hours
Pedestrian traffic 24 hours
Light traffic 2 days
Total curing 7 days

For non-slip finishes, dusted silica sand with a granulometry of 0.4-0.9 Kg/m2 or higher should be added to the product depending on the degree of slip desired.
It can also be added with 0.2-0.4 mm dry silica sand to apply as a regularization layer and as self-leveling layers (mixing proportions: 2 parts of resin for every 1 part of sand, by weight).

Maintenance and cleaning: To maintain the appearance of the floor after application, all spills must be removed immediately after they have occurred. The floor must be cleaned regularly using rotating brushes, high-pressure cleaners, vacuum cleaners, using neutral detergents and appropriate waxes. Once the container is opened, we recommend its complete consumption. Once the two components have been mixed, the mixture obtained must be applied, respecting the pot-life.

Stable for 12 months from its manufacturing date, in its original, well-closed and undamaged container. Store in a dry and cool place at temperatures between +5ºC and +25ºC.
Application in closed areas must be carried out ensuring proper ventilation during application and 48 hours after.
Do not exceed the maximum consumption because it may affect its adhesion and durability.
Avoid the formation of puddles of the product.
In applications exposed to U.V. rays. yellowing may occur. It is recommended to protect with a topcoat of pigmented aliphatic polyurethane.
For applications with chemical resistance, consult the technical department.
Incorrect treatment of cracks and singular points can lead to a reduction in the useful life of the pavement.
To clean materials and utensils, use FUTURSOLVENT 001 before the product hardens. Once the product has hardened it can only be removed by mechanical means.

• Very useful in all types of construction companies, quick repair contracts, general masonry, community maintenance, repair and restoration of buildings, industrial flooring, etc.
Application as:
• Treatment, decoration and protection of pavements, floors and rehabilitation of: Industrial Floors, Food Floors, Chemical Resistance Floors, Floors resistant to vehicle traffic (light traffic), industrial warehouses, warehouses, Shopping Centers, Cold Rooms, etc.
• Dust and anti-wear protection of concrete.
• Compatible with concrete floors, mortar, mosaics, ceramics, tiles, etc.
• Floor covering in poorly ventilated areas.